Pioneer SA-8800 integrated amp (Used)

Special Version for Japanese High End Market.Beatiful Cosmetic condition.Very heavy 13.8 kg

S$ 210 SGD only

110V needs step down transformer.

Posting for a friend.

Pick up area Jurong, yung kang road. Sms to 92208000 John,

Look at the two transformers:




Specs:
Form Stereo Integrated Amplifier

Circuit system 2 steps of differentials whole page hardwired-connection parallel PP pure complimentary OCL
Effective output
(Both channel drive, 20Hz - 20kHz) 75W+75W (4ohm)
60W+60W (8ohm)
THD (20Hz - 20kHz) 0.05% (at the time of an effective output)
0.01% (at the time of 30W output 8ohm)
0.01% (at the time of 1W output 8ohm)
Cross modulation distortion (50Hz:7kHz=4:1) 0.05% (at the time of an effective output)
0.01% (at the time of 30W output 8ohm)
0.01% (at the time of 1W output 8ohm)
Output bandwidth (IHF, both channel drive) 5Hz - 45kHz (0.05% of distortion)
Frequency characteristic 5Hz-100kHz+0 -1 dB
Input sensitivity/impedance Power amp in: 1V/50kohm
Output-terminal Speaker A-B: 4ohm-16ohm
Speaker A+B: 8ohm-16ohm
Headphone: 4ohms - 16ohms
Dumping factor 30 (20Hz - 20kHz, 8ohm)
S/N 110dB (IHF, A network, a short circuit)

Circuit system Equalizer-amplifier part: 3 steps of first rank differentials hardwired-connection Class-A SEPP
Tone control part: 2 steps of first rank differentials hardwired-connection flat amplifier,
3 steps of turnover switching NFB type tone
Input sensitivity/impedance Phono1, 2:2.5mV/50kohm
Cartridge load capacity: 100pF, 200pF, 300pF, 400pF (Phono1 and 2)
Tuner, Aux, Tape play1, 2:150mV / 50kohm
Phono maximum permissible input Phono1, 2:250mV (1kHz, 0.05% of THD)
An Output voltage/impedance Tape rec1, 2:150mV
Pre out: 1V/2kohm, 6V/2kohm (max)
THD (20Hz - 20kHz) 0.02% (1V output)
0.1% (6V output)
Frequency characteristic Phono: 20Hz-20kHz±0.2dB
Tuner, Aux, and Tape play:5Hz-50kHz+0 -1 dB
Tone control Bass: ±10dB (25Hz, 50Hz, 100Hz)
Turnover frequency: 100Hz, 200Hz, 400Hz
Treble: ±10dB (8kHz, 16kHz, 32kHz)
Turnover frequency: 2kHz, 4kHz, 8kHz

Filter Low: 15Hz, 6dB / oct
High: 8kHz, 6dB / oct
Loudness contour
(Volume -40dB) +6dB(100Hz)
+3dB(10kHz)
Muting -20dB
S/N (IHF, A network)
Short circuit Phono:75dB
Tuner, Aux, Tape play: 95dB

The semiconductor used Transistor: 47 pieces
Diode,others: 27 pieces
AC outlet Power-switch interlock: Two lines
Power-switch un-interlocking.: Two lines
Supply voltage AC100V, 50Hz/60Hz
Power consumption 150W (Electrical Appliance and Material Control Law)
410W (maxima)
Dimensions Width 420x height 150x depth of 376mm
Weight 13.8kg

The Integrated Amplifier which pursued high-quality sound-ization, such as adopting 2 power transformers of a right-and-left independency in order to improve a dynamic behavior.

While having adopted a differential, a three-step hardwired-connection final-stage Class-A operation, pure complimentary SEPP, and positive/negative 2 power source of the first rank as an equalizer part and aiming at a distorted reduction,The modification of a property is aimed at by using the NFB element (±1% of an error, the nichrome vapor-deposition metal film resistor of temperature characteristic±50 part per million/c, styrene capacitor of ±2% of an error) selected carefully.
Moreover, the improvement in an SN ratio was aimed at by selecting carefully and adopting especially a low-noise transistor as the first rank differential amplifier, and 250mV of maximum permissible inputs have been obtained by supplying the voltage of ±25V to a circuitry.

In order to demonstrate the performance of various cartridges, the circuit changing switch from which four kinds of cartridge load capacity can be chosen is carried. The load capacity which was suitable for the using cartridge by this can be set up.

The two-step hardwired-connection flat amplifier of a control part chooses the operating point as the linear area of a transistor by making the first rank into a differential amplification, and is aiming at the distorted reduction. Moreover, the tone control has adopted the 3 steps of turnover switching.
It is adopted as a control knob with the click stop which is easy to use, and also also has the tone on-off switchpoint.

The attenuator type of 32 steps is adopted as a volume, and there is little gang error between right-and-left channels as less than 0.5dB, and it also serves as indicated value of the panel side with an error of less than ±0.5dB.
Furthermore, it has a muting lever of -20dB, and more delicate volume control is possible.

The circuitry of the power amplifier part consists of a 2 steps of ±2 powering and differentials amplification current mirror circuitry, a final-stage parallel push pull, and a pure complimentary OCL circuitry.
The dual transistor where the property was stabilized is used for the differential-amplification part of the first rank, and it is reducing the eventh harmonic content by considering a pre driver or later as a push pull drive while making the pre-driver stage into a current mirror circuitry, applying sufficient NFB and reducing distortion.
The good chimney style radiator of the heat-dissipation effect is adopted as a heat dissipation.

The power-source part had adopted two power transformers and the capacitor of 10,000 micro Fx4, eliminated the cross interferencee between channels in the power-source part, and has improved the channel separation.

The protection network consists of quick electronic circuitries of a power relay and a response.
Moreover, the it1 sound at the time of power activation is also eliminated.

Functionalities, such as a separation termination of a preamplifier and power amplifier, a two-line tapes monitor and a loudness contour, a low cut (subsonic speed), and a high cut-off filter, are carried.